Skip to the beginning of the images gallery

Double Wire Braid SAE 100R16 Type S Hose, 0.63 Inch ID, Up to 4000.00 PSI

Abrasion Resistance 28	Burst Pressure 16000	Conductivity 30	Cover Material Synthetic Rubber	Brand Danfoss Power Solutions (II LLC Aeroquip)	Brand Aeroquip	Pack Size 12.00	UOM FT	Hose I.D. 0.63	Hose O.D. 0.93	Impulse Cycle Life 600000 B7	Lay Line Style Ink Transfer	Maximum Operating Pressure 4000	Minimum Bend Radius 4	Minimum Bend Radius 4	Minimum Working Temperature -50	Reel Qty (ft) 225-300	Reinforcement Material Wire	Supplier Part Number GH781-10R250	Tube Material Synthetic Rubber	Alternate Part Numbers Alternate Part Number C1CX58, Alternate Part Number GH781-10, Alternate Part Number GH781-10-100, Alternate Part Number GH781-10-50, Alternate Part Number MI-03749662, Alternate Part Number MINO-00015X00020	Product Weight 0.54 lbs

Product Questions & Answers 4

Product Questions & Answers

got a piece of equipment that sits outside year round so it sees freezing cold and gets real hot running in summer. can i run regular hydraulic fluid thru it

Question by: Stan W on Jun 5, 2025, 12:35 PM

Temperatures between -40 and 212 degrees Fahrenheit are fully supported by the synthetic rubber tube and cover. You can safely run both petroleum-based and water-based hydraulic fluids through the line for general service.

Answer by: Customer Support on Jun 7, 2025, 11:32 AM

got a job where space is tight. how sharp can this hose bend without kinking up?

Question by: Billy P on Sep 5, 2025, 6:58 AM

Minimum bend radius on this hose is 4 inches. Keeping your routing at or above that radius helps it hold shape and avoid stressing the double wire braid.

Answer by: Customer Support on Sep 6, 2025, 9:58 PM

got a tight spot to route this line, how sharp can i bend it without kinkin it

Question by: Ronnie B on Oct 15, 2025, 1:59 PM

For routing, the published minimum bend radius is 4 inches. Keeping your bend at 4 inches or larger helps prevent kinking and protects the wire braid reinforcement.

Answer by: Customer Support on Oct 17, 2025, 6:49 AM

burst pressure on this one is listed at 16,000 PSI -- that seem right for a half-inch hose running 4000 working pressure?

Question by: Ray A on Apr 8, 2025, 7:03 AM

that 4-to-1 safety ratio is exactly what you'd expect on a hose rated to this spec. The working pressure tops out at 4000 PSI and the burst is confirmed at 16,000 PSI, so the margin is solid. For most hydraulic service running petroleum or water-base fluids, that ratio holds up well under normal operating conditions.

Answer by: Customer Support on Apr 9, 2025, 2:17 PM

Similar Products

Model Number	Hose I.D.	Hose O.D.	Maximum Operating Pressure	Burst Pressure	Minimum Bend Radius	Reel Qty (ft)
GH781-10R250	0.63	0.93	4000	16000	4	225-300
GH781-4R500	0.25	0.53	6500	26000	2	450-550
GH781-6R500	0.38	0.69	5300	21200	2.5	450-550
GH781-8R500	0.5	0.81	4500	18000	3.5	450-550
GH781-16R150	1	1.42	3000	12000	6	125-200
GH781-12R250	0.75	1.1	3500	14000	4.75	225-300
GH781-20	1.25	1.65	2500	10000	8.25	Rolls Only
GH781-24	1.5	2.03	2000	8000	10	Rolls Only
GH781-32	2	2.53	1600	6400	12.5	Rolls Only